/r/czscorpion
/r/CZScorpion Is home to information and accessories for the CZ Scorpion EVO 3 / 3+ and the Nexus EVO Gen 1
This sub is dedicated to information and accessories concerning the CZ Scorpion pistol and carbine. We consider ourselves a friendly community so feel free to ask questions and post your builds! In order to upvote and/or downvote please subscribe.
NO FIREARM SALES OR TRADES
SELLING SCORPION ACCESSORIES IS ALLOWED ONLY BY POSTING ON r/gunaccessoriesforsale AND CROSS POSTING! NO DIRECT SELLING ANYTHING HERE!
Posts not following these rules will be removed.
Check out our Wiki
Please Visit our Supporters!
Related Subreddits
Reddit Gun Network Subreddit List
Remember Firearm Safety
Everyone is a Range Safety Officer, if it seems unsafe call
In addition:
Suicide and Guns
Suicide is a serious problem all around the world. If you or someone you know is considering suicide please help them. There are many resources available for veterans and civilians alike. Don't let yourself or another fall to suicide.
Sucide Prevention Lifeline Website or call them at 1-800-273-8255
For international help please visit Suicide.org's Hotline Finder to get in touch with the assistance available to you in your country.
You can make all the difference in someone's life.
/r/czscorpion
What are you running for a VFG? Looking for recommendations, thanks!
Finally joined the club
Anyone know where I can buy the faux suppressor that comes on the 3+?
Anyone using this can ? I'm looking at this for my first.
I installed a Manticore CZ Scorpion tri lug mount on my gun and a KAW Valley 9mm tri lug adaptor on my obsidian 45 can. The can seems to fit very tight on the small raised part of the tri-lug mount (see picture below). Once on I can lock and un-lock the can, but to remove it from the gun, I have to use a rubber mallet. Anyone have this issue before? Thoughts on how to fix it? I was thinking of sanding down the raised lip on the tri-lug muzzle device.
Picture
https://imgur.com/6SfAcsl
My scorpion as it sits. Waiting on the nexus receiver and hbi handguard as I don't really even care to shoot it much anymore till I have those installed. It went kablooey once and cz "fixed it" but I still went ahead with the nexus bolt. A couple other pistols I got laying around to go with just for fun.
Wondering if there’s a way to remove a muzzle device that’s inside the hand guard once it’s set with high temp thread lock, without messing up the handguard on the micro 3+.
I don’t intend to take the cherrybomb muzzle device off, but I was curious if it pretty much becomes permanent due to inability to reach the threads with direct heat.
doesanyone k ow where I can get thw red tritium sights from the A1 scorpion? can't seem to track them down.
Hey all, I just installed a 4” HBI handguard and I’m utilizing the factory charging handle, I’ve noticed a lot of friction and determined it is coming from the handguard passage for the charging handle. Specifically it looks like the charging handle is riding the inside of the passage very tightly as indicated in my picture. Is this due to the passage being out of spec or the charging handle? Has anyone else experienced this with their HBI handguard?
I have a suppressor coming in this week, and I’ve been trying to figure out if I put a low profile direct thread mount on, will I have to remove anything to install it, or will it just thread onto here? (I’m not a gun expert and still trying to learn)
This was my second time taking the Scorpion to the range after adding the angled foregrip, stock, and red dot.
Just got the call. Took 30 days on a trust and batched three suppressors.
I’m waiting on the acro mount and it’ll be done!
This looks so good
What gun accompanies your Scorpion? For me, I have a Henry Model X, 30-30, with loads of aftermarket work. I often bring these both to the range and I always get questions and compliments. They are both so fun to shoot!
I have an Evo 3 S1
Am I regarded here?
I didn’t ordered the wrong one unless HBI sent the wrong one.
Do I file it down?
Thanks!
Have had my scorpion for 4 or so years. Factory carbine that I converted to a SBR micro with the hbi kit. No binary trigger, not mag dumps or hot ammo. All 115 grain federal, probably 1k rounds, maybe a little more. I was cleaning today and noticed this. Due to the wear, the striker block is pushed down some. I found a video about a test you can do with the firing pin. My will poke out with or without pressing on the striker block. So… am I next for OOB? I was just looking at a zenith zf5 the other day and told myself that I don’t need it. Now I’m thinking I do!
I see some of you have a stock for short barrel scorpion. This is a question for those folks. What made you SBR the thing? Is there noticeable difference on how it handles between brace and stock?
Is there a pic of the non us scorpion bolt that shows the difference between the euro one vs the us model?