So I travel for work and am looking for a full states complacent all around hunting rifle, I think marlin 30/30 fits that criteria just looking for advice or insight Also advice on a scope to put on it

Hey guys, I just got an 1897 but I am missing the screw that holds the magazine tube to the barrel. I have tried the usual sites and havent found anything. Any suggestions?

Evidently my model 60 marlin semi auto .22 is a one off yr. I only see one confirmed case of a model 60 marlin 22 with the prefix MM. From the site oodmag.com I saw the info """As of late 2013, a Marlin .22 RF rifle (XT-22 Mag) had a serial number prefix of MM reported and verified. It is unknown as of December 2013 how Marlin ("Remlin") will continue with their serial numbering convention"" I want to buy parts for my .22 but I can't decode the serial number to tell me any information. The barrel says "" THE MARLIN FIREARMS CO. MAYFIELD KENTUCKY USA MODEL 60 MICRO - GROOVE BARREL CAL 22 LR ONLY ""

I have a marlin 1898 in the shop to be deemed safe and ensure all parts are safe and in working order. According to my Gunsmith it is one of the earlier models, I believe that it takes 2 5/8 black powder shells. Am I correct? And if so where can I find such shells or shells that will be fireable. I'm fully aware of the safety concerns so please leave that out of the equation. This gun will mostly sit on display but I want to be able to shoot it in my field every now and then

when did Marlin sell out to Ruger? i just noticed the "Pre-Ruger Manufactured"..

​

https://preview.redd.it/cbw0w4lpffcc1.png?width=2880&format=png&auto=webp&s=75ef5dd35bea362d701fe42732b06aea5c6e600f

I recently got the Rapido Plus Hotend but i cant find any sort of documentation how i set it up in Marlin firmware. The hotend uses the PT1000 thermistor.

The Printer is a direct extruder Ender 3 V2 with Ldo Orbiter 2.0 and the Phaetus Rapido Plus Hotend.

So I came across a 1895M ( 450 marlin) for super cheap ( project gun), wasn't able to pass up the deal. I have had it for about 9 months now and have been looking everywhere for a new magazine tube. The one that came with it had been pretty much folded in half. I have been able to straighten it out as much as possible. It's at the point that rounds will drop freely through it however, the follower keeps getting caught and 1 spot that I can't seem to get the bend out. I have looked everywhere for a new tube. Was just curious if anyone has one, or knows of a place that I could get one. Thanks

Inherited this gun and have a bunch of 30-30, it's chambered for .35 but would it work with 30-30?

Does anyone know if it is possible to get a spare bolt for a Marlin xs7? I have lost mine

Anyone got answers on what magazine to buy?

Sold out everywhere I look. Any thoughts on availability?

I posted a few days ago looking for a wood rifle stock for a Marlin XT-22M. I have searched the internet all over looking for a wooden stock replacement and can't find one that doesn't cost more than I paid for the rifle. I found a Marlin 980 stock in my price range and I think it might work. Midwest Gun Works has them listed (out of stock) and it says it fits the 920, 925, 925M, 980SD, XT22 and XT-22M. It looks like one stock fits all these models. Is there anyone out there that can tell me if it's the same stock as the XT22M?

I have a Marlin XT22M, bolt action, mag fed rifle. I t came with a "synthetic" stock. I would love to change to a wood stock but I can't find one anywhere online. I don't mind it it's used as long as it's not damaged where I can refinish it. Can anyone point me in the right direction?

Anyone know when Marlin will start producing model 336 lever guns again? Seems like most production is focused on their 45-70 models. Would like a 30-30 and their finish and design just looks better than Winchester and Henry (IMO).

Hi Folks! I just installed an SKR Mini E3 V3.0 into my Ender 5 Pro (far from stock, I have the upgrades outlined below).
I'm running into an issue with compiling Marlin for the new board. I can't find anything for the Mini E3 V3.0 board for the Ender 5/5Pro. I see that BigTreeTech has a precompiled firmware.bin file on their GitHub page for the Ender 5 Pro, but seeing that I am not running stock hardware, I would need to make changes to the configuration. Should I just start with an Ender 3 configuration example and make changes from there? Or is there a better starting point for me to customize the Marlin firmware. Thanks a ton!

Upgrades:

• SKR Mini E3 V3.0
• CR Touch
• All Metal Hotend
• Noctua Fans (hot end, motherboard)
• Direct Drive

I have just bought, although still have not yet received, a Marlin 1894 CP in .357 and my main intention s with the rifle was getting it threaded for a suppressor, and since its ported thats raised a few questions for me.

Can you actually thread a rifle thats ported?

and is there any point in it?

Looking at aftermarket sights, preferably ghost ring long radius for my 336. Would prefer something where i can keep the factory front sight. Most things i see replace front and rear.

Thanks!