https://portablismgear.com/sc1000.html

Just a heads up for people looking to get one. The last batch of this year according to their IG.

I see Jesse Dean has brought a new tonearm and fader out for the RS. Great to see the RS is still getting mods. I think I'll get the new tonearm, looks much better than the previous one.

There's also a new touch fader which cuts the audio when touched. I'm not going to bother with this. What I don't understand though, is that on the installation video, he shows one being installed on the left hand side with one of his regular faders being installed on the right hand side. If this was the case, then how would you control the volume of the vinyl audio? Doesn't everyone who uses a RS control the vinyl audio with the fader that is not used for cutting or am I missing something? Is there another way to control vinyl volume?

Can the headshelll on a stanton stx be changed

So I have a Numark PT01 Scratch and Serato control vinyl. I want to scratch my own samples and record into my DAW. A while back someone suggested an old Akai AMX which I have just bought for £50. My question is do I have to use Serato for this to work or can I use another app such as MiXXX to avoid paying Serato 9.99pm for DVS?

Hope I have not bought the wrong thing (already bout a Mixfader which was a none starter).

Thanks in advance

Hey there people from the group🤘🤘 Anyone here from Switzerland?

Is there any videos on how to re callibrate sharo cuts for the innofader on SC500?? it started bleeding after using it about 10 times.... any tips ?

Does anyone know where to find one?

It’s been over a year of searching and I cannot find a sc500 anywhere! They’ve been sold out for so long, and I can’t find anything on aftermarkets.

Please point me in the right direction

Thank you!

Hi there

I’m very new to portablism and so far I’ve been scratching 7inch vinyls over Spotify instrumentals and having great enjoyment doing so. I’ve installed 18650 batteries and my next focus is to try and venture into the DVS mode Omni possesses . So far I’ve completely failed to set this up. I’m way over my head being honest with you . I’ve no DJ experience what so ever ,this is all completely a hobby to me.I tried to set it up using dj player pro on the iPhone and bought the camera charger it mentions in the Omni instructional videos but I fail to get a signal. I was told to download mixxx to my laptop which I’ve done but again I’ve no idea what I’m doing . Does anyone have a walkthrough video or instruction for dummies 😂, I’d really love to explore this feature further. I bought Serato control vinyl but haven’t a clue what I’m doing . I’d like to find out am I also meant to buy a music Catologue subscription of some kind and what would you recommend for HipHop samples

So sorry for the long post but I need to begin the journey somewhere 😉. Thanks for your time

Hello all, Simply would like a recommendation for a DJ program to use the DVS capabilities. I use a lot of serato apps (studio, sample) and would love to use DJ Pro, but can I? Open to whatever works best though. Thanks in advance!

Any 7 inchers with guitar? Love to get my hands on little record with screaming solo guitar.. .

What is anyone using for some thing comparable to the Raiden RPM-100

howdy,

i've had an sc500 for a few years that worked about two times. turns on, low volume click, pause, few seconds of low volume noise while the USB drive blinks, silence and the drive's no longer flashing/being read. the internal LED of the unit itself remains on. i've tried several drives and have tried re-formatting a dozen times across said drives; any time i test and return the drive to my PC it immediately needs to be re-formatted anyway.

the weird thing is, it was still able to take a firmware update following instructions off http://rasteri.com/wiki/SC1000_Firmware_Update just this morning, behaved as expected there. yet i cannot get the unit as far as playback from either folder.

the power supply is 5v/2.4a, and the cable i'm using i bought years ago when troubleshooting with portablism - it should be rated for the needed charging strength. i've tested with four other cables but same lack of result.

folder structure on my USB https://imgur.com/a/wQUxDpg for posterity's sake

--at this point is it worth opening this thing up? i don't have a great deal of experience in soldering and have zero idea where to begin with further troubleshooting, and i'd really rather it not remain a paperweight. i wanted it to be a part of my production years ago, and still do. any advice is appreciated.

All the DVS mods for the PT-01 that I've seen require an external audio interface like a Rane SL1, but the PT-01 already has a stereo input & output PCM2900 USB codec built in, the output just isn't routed anywhere.

The phono control tone is already wired to goto two locations. First to the USB codec which we'll need for the DVS control input and second to the speaker/headphones output. I'm using the PT-01 for DVS exclusively, so I've replaced the control tone that normally goes to the speakers/headphones with the output from the USB codec, which is my DVS audio.

The built-in crossfader switch in my PT-01 Scratch still cuts the DVS audio as before.

For DJ software, I'm using Tau DJ (previously DJ Player Pro). In iOS the USB phono gain was reported as too Hot & Distorted for Tau DJ. There's no control knob to change the USB phono gain or in iOS, so I had to reduce the gain in HW. If you're not in iOS you can skip this step.

This solution will not work with Algoriddim. I don't know if EDJing will work. Mixxx will work.

Thanks to u/rasteri for laying the groundwork.

http://rasteri.com/wiki/Numark_PT-01

PCM2900 pinout

Zoom'd out view of the USB port

Only needed for iOS. Changing the Phono Gain from 3x to 2x.

DVS Audio output comes out of these two pins. Wire from here to the Fader input on the Control board.

Zoom'd out view of the Control board

Control tone comes through R34/R22; remove resistors to break signal path. Wire from Codec output to Fader input. I also ran an additional GND wire from the Control board to the USB board.

Recently, I got a 7-inch Serato vinyl, and I intend to use it with my Reloop Spin. My question is, to use it as DVS, do I just need to connect an RCA cable to the Reloop Spin on one end and connect the other end to an audio interface, and then the audio interface to the PC? Is that all? If so, will the Behringer U-Phono UFO202 audio interface work for me, or do I need another one? Also, if you could explain the difference between Phono and Line outputs, I would really appreciate it.

SC1000 & SC500 Digital Scratch Instrument (portablismgear.com)

Hey guys so i was wondering how to install the Straight arm for the Stanton Stx that you can buy on the portablism website. If anyone could give me a rundown of what to do id really appreceate!

DJ Tools

🎛️ Level Up Your Portablism with High-Quality Sounds from DJ Tools! 🎛️

Are you a turntablist or portablist looking for fresh, high-quality sounds to add to your routines? 🎚️ DJ Tools has exactly what you need! Our collection of scratch sounds and samples are designed to give you the edge in your performances, whether you’re battling, practicing, or rocking live sets.

🔥 What You’ll Find:

• Exclusive scratch samples designed for smooth cuts and precision.
• Sound effects that add flair and creativity to your routines.
• Battle tools to help you dominate in competitions or jam sessions.
• Perfect for both beginner and pro portablists!

Ready to enhance your performance? Visit DJ Tools and start building your next killer routine with the best sounds in the game.

Yo I'm looking for "Killer Portable Zombie Cutz" on crab cake records..happy to import uk if needed.

https://youtu.be/K7JsMxJ4kGs?si=CcQBuVkWJBh4Nq0B

Power just stopped working one day. I barely used it. Really pissed me off because it’s passed the warranty and Amazon wouldn’t honor it or seller. I bought 8 DD’s and it works with batteries. Just frustrating

Recently got into scratching records with the pt01 numark and 6 hours in I notice a lot of dust. Sound quality is also lost at the beginning of the record since I’ve been taking my time learning the baby scratch and other beginner stuff. Just wondering how long these “practice yo cuts” records last other people. Any tips on how to prolong the life of these records is also much appreciated.

Hi guys, I've got problem with my jddpta for pt01 scratch, just installed give power issue to my numark due to the preamp of jesse dean, what can I do to solve the problem?

Anyone know where I can get different color top acrylic panels? Just want to make mine different.

Im a total newb. Have a headphone jack out from sc500 to usbc adapter connected to android. Android thinks it's an output. Can I change it to input somehow or what do I need to do?

I’m looking to purchase a OMNI PORTABLE DVS TURNTABLE V.2 as a gift. Everywhere seems sold out online. Can anyone recommmed an trustworthy online seller with stock available? Thanks in advance.

Hi everyone, i have a Mackie profx10 v3 mixer with inserts on my turntable Channels. I've set my turntable to be on the First two channels of the mixer, so One Channel for Right Signal and One for Left. Then i bought a Stokyo Kutter portable crossfader in order to be able to scratch. Then i connected an insert cable (Y shaped, so three 1/4 jacks endings) to the in and out of the Stokyo Kutter, and the last jack to a splitter cable, which goes in the inserts spots on the Mackie Mixer. I hope my explanation has been clear and not confusing, but the point Is that no sound Is coming out of the master, nor the control room. Hoping this is not OT, i wonder if any of you have experience with Stokyo Kutter outside of the portablism way. Thanks for the attention Peace 😊